Pin Belegung TürStg

Hello, here is the problem: I have g5 tdi 2005, and bought
power window module with lifter, and wiring in the door from g5 2008.
The control modules are the same in the front door, but I have an issue
with the wiring. As far I was googling, I found the old wiring diagrams,
probably they changed the shemas. There is a plum/white wire on Pin 6
at the door 28 pin A-pillar and B-pillar connector, that is the same
wire in drivers TürStg 20pin 15th pin, and rear door 18pin 12th pin.Is it connected directly from the drivers door to the passenger door and the rear doors? All the TürStg modules are comucating by the plum/white wire?

Pin 1 ro/ge = Plus Klemme 30

Pin 4 or/gn = can low

Pin 5 or/br = can high

Pin 6 li/ws = zu TürStg. Fahrerseite hinten

Pin 11 ws = zu TürStg. Fahrerseite

Pin 12 ro = Airbag Crashsensor

Pin 13 br = Airbag Crashsensor

Pin 21 br = Masse

Pin 22 ro/ge = Plus Klemme 30

Pin 23 ro/bl = Lautsprecher + (Bei Weiche in der Tür)

Pin 24 br/bl = Lautsprecher - (Bei Weiche in der Tür)

Thank you very much! [Blockierte Grafik: http://www.klangfuzzis.de/images/smilies/grins.gif]

Zitat von datajam

Hi, there ....

I'm not able to follow you.

Where do you wanna change the Modules.
Within the front or rear doors.

If youre trying to change the Rear Door Control Modules.

You ve 2 change them from CAN 2 LIN.
Its not been done by changing the door wiring only.
Additionaly you ve 2 retrofit the LIN wiring to the rear doors.

But its not all, probably you ve to change your Central Electronics Module
to.

Further its not possible to put the rear DCM in the Front doors.
Cos they still are connected by CAN.

Regards

Alles anzeigen

Zitat von datajam

Hi, there ....

I'm not able to follow you.

Where do you wanna change the Modules.
Within the front or rear doors.

If youre trying to change the Rear Door Control Modules.

You ve 2 change them from CAN 2 LIN.
Its not been done by changing the door wiring only.
Additionaly you ve 2 retrofit the LIN wiring to the rear doors.

But its not all, probably you ve to change your Central Electronics Module
to.

Further its not possible to put the rear DCM in the Front doors.
Cos they still are connected by CAN.

Regards

Alles anzeigen

Zitat von datajam

Hi, there ....

I'm not able to follow you.

Where do you wanna change the Modules.
Within the front or rear doors.

If youre trying to change the Rear Door Control Modules.

You ve 2 change them from CAN 2 LIN.
Its not been done by changing the door wiring only.
Additionaly you ve 2 retrofit the LIN wiring to the rear doors.

But its not all, probably you ve to change your Central Electronics Module
to.

Further its not possible to put the rear DCM in the Front doors.
Cos they still are connected by CAN.

Regards

Alles anzeigen

Sorry, here is more info! I have manual window lifter rear, front power. I bought rear lifter with motor and module 2x, wiring harness to the pillar until the rubber part 2x, and I get the driver door harness too, but that is exactly the same as I have at the moment just the plum/white pin missing. Normally the rear door wiring is different, only 4 wire is in, ground, dauer plus, klemme 30, and the plum/wire. I already made the harness to rear door, in the car, klemme 30, the power, ground, but I did not find the information, where do I connect plum/white, just found the info to bypass from the drivers door 20pin/15 to the rear door 18pin/12th pin.

1K0 937 049 N BnSg 21byte higline

1k0 959 701/2 E TürStg in front doors

1k0 959 433 AK Comfort Stg 4teuer

This is the equipment at the moment. What do you think, is it smart enough to control the rear modules?